INSTRUMENT PANEL SAFETY PAD > INSTALLATION |
for Preparation Click here
1. INSTALL INSTRUMENT PANEL CUSHION |
2. INSTALL NO. 1 INSTRUMENT PANEL PIN |
Install the 4 No. 1 instrument panel pins with the 4 screws <D>.
3. INSTALL ANTENNA CORD SUB-ASSEMBLY |
Engage the 4 claws and install the Radio antenna cord.
4. INSTALL INSTRUMENT PANEL CENTER BRACKET SUB-ASSEMBLY |
Install the instrument panel center bracket sub-assembly with the screw <D>.
5. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
Install the instrument panel register with the 4 screws <D> with the fins closed.
6. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY |
7. INSTALL DOOR CONTROL RECEIVER |
Install the door control receiver with the 2 screws <D>.
8. INSTALL 4 WHEEL DRIVE CONTROL ECU |
Install the four wheel drive control ECU with the 2 screws <D>.
- Torque:
- 1.2 N*m{ 12 kgf*cm , 11 in.*lbf }
9. INSTALL DEFROSTER NOZZLE ASSEMBLY WITH NO. 2 HEATER TO REGISTER DUCT |
Install the defroster nozzle with No. 2 heater to register duct with the 5 screws <D>.
10. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY WITH PASSENGER AIRBAG ASSEMBLY |
Install the instrument panel sub-assembly with passenger airbag assembly with the 8 bolts and nut.
- Torque:
- 20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>
Engage the 5 clamps and connect the 4 connectors.
Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.
11. CONNECT PASSENGER AIRBAG CONNECTOR |
12. INSTALL INSTRUMENT SIDE PANEL RH |
Engage the 3 claws and install the instrument side RH.
13. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY |
Connect the connectors.
Engage the 5 clips and install the instrument lower cover.
Install the bolt <B>.
14. INSTALL LOWER INSTRUMENT PANEL LH |
Install the lower instrument panel LH with the 3 bolts <B>.
15. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH |
Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.
Install the bolt <B>.
16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
Pull the bottom of the stopper.
Attach the stopper to the glove compartment door as shown in the illustration.
Install the glove compartment door assembly with 3 hinges, holding it horizontal.
Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.
17. INSTALL INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY |
Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.
18. INSTALL COMBINATION METER ASSEMBLY |
Connect the 2 connectors.
Install the combination meter assembly with the 4 screws <E>.
- Torque:
- 1.7 N*m{ 17 kgf*cm , 15 in.*lbf }
19. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
Connect the connectors.
Engage the 6 clips and install the instrument cluster finish panel sub-assembly.
Install the 2 clips.
20. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.
Install the 2 bolts <B>.
21. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Connect the hood lock control cable assembly.
Engage the 2 claws and install the hood lock control lever sub-assembly.
22. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) |
Connect all the connectors.
Engage the 5 clips and install the radio and display receiver assembly with bracket.
Install the 4 bolts.
- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
23. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System) |
Connect all the connectors.
Connect the plug.
Engage the 5 clips and install the radio receiver assembly with bracket.
Install the 4 bolts.
- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
24. INSTALL AIR CONDITIONING CONTROL ASSEMBLY |
Connect the 2 connectors.
Engage the 4 clips and install the air conditioning control assembly.
25. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the clip and 2 bolts <A>.
Install the 2 instrument panel cup holders.
Install the box bottom mat.
Install the shift knob.
26. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the clip and 2 bolts <A>.
Install the 2 instrument panel cup holders.
Install the box bottom mat.
Install the shift knob.
27. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
Install the shift knob.
28. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type) |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
29. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) |
Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.
Install the 2 instrument panel cup holders.
30. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
Engage the 4 claws and install the console box rear.
Install the 2 screws <F> and 2 bolts <B>.
Install the console box carpet.
31. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type) |
Engage the 4 clips and claw, and install the console upper panel sub-assembly.
32. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type) |
Engage the 6 clips and claw, and install the console upper rear panel.
Install the shift knob.
33. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
Engage the 4 clips and install the instrument panel hole cover.
34. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
Engage the 4 clips and 2 claws, and install the instrument panel under tray.
35. INSTALL FRONT PILLAR GARNISH LH (for Regular Cab) |
for LH Side:
Install the 3 wire harness clamps.
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
Engage the 2 claws and install the assist grip plug.
36. INSTALL FRONT PILLAR GARNISH LH (for Access Cab) |
for LH Side:
Install the 3 wire harness clamps.
Engage the claw and clip, and install the front pillar garnish and assist grip.
Tighten the 2 screws.
Engage the 2 claws and install the assist grip plug.
- HINT:
- Follow the same procedures as for the opposite side.
37. INSTALL FRONT PILLAR GARNISH LH (for Double Cab) |
Install the 3 wire harness clamps (LH side only).
Engage the claw and clip, and install the front pillar garnish.
Tighten the 2 screws.
Engage the 2 claws and install the assist grip plug.
- HINT:
- Follow the same procedures as for the opposite side.
38. INSTALL FRONT PILLAR GARNISH RH (for Regular Cab) |
- HINT:
- Follow the same procedures as for the front pillar garnish LH.
39. INSTALL FRONT PILLAR GARNISH RH (for Access Cab) |
- HINT:
- Follow the same procedures as for the front pillar garnish LH.
40. INSTALL FRONT PILLAR GARNISH RH (for Double Cab) |
- HINT:
- Follow the same procedures as for the front pillar garnish LH.
41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
43. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
44. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
45. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
46. INSTALL COWL SIDE TRIM BOARD RH (for Regular Cab) |
- HINT:
- Follow the same procedures as for the cowl side trim board LH.
47. INSTALL COWL SIDE TRIM BOARD RH (for Access Cab) |
- HINT:
- Follow the same procedures as for the cowl side trim board LH.
48. INSTALL COWL SIDE TRIM BOARD RH (for Double Cab) |
- HINT:
- Follow the same procedures as for the cowl side trim board LH.
49. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
Engage the 8 claws and clip, and install the front door scuff plate.
50. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab) |
Engage the 9 claws and clip, and install the front door scuff plate.
51. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab) |
Engage the 9 claws and install the front door scuff plate.
52. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab) |
- HINT:
- Follow the same procedures as for the front door scuff plate LH.
53. INSTALL FRONT DOOR SCUFF PLATE RH (for Access Cab) |
- HINT:
- Follow the same procedures as for the front door scuff plate LH.
54. INSTALL FRONT DOOR SCUFF PLATE RH (for Double Cab) |
- HINT:
- Follow the same procedures as for the front door scuff plate LH.
55. INSTALL FRONT FLOOR FOOTREST |
Engage the 2 clips and install the front floor footrest.
56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
57. INSPECT SRS WARNING LIGHT |