UPPER INSTRUMENT PANEL (for Hatchback) > INSTALLATION



1. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Engage the 5 guides at the front of the upper instrument panel.

    NOTICE:
    Be careful not to damage the upper instrument panel and steering wheel when installing it.
  1. Engage the 8 clips at the rear of the upper instrument panel.

  1. Install the <B> bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
  1. Install the upper instrument panel with the 2 clips.



    B284264
  1. Connect the passenger airbag connector.



2. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the 2 connectors.

  1. Engage the 2 guides and 2 clips.

  1. Install the combination meter assembly with the 2 screws.



3. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL
  1. Engage the 5 clips and install the instrument cluster finish panel.



4. INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY
  1. Connect the connector.

  1. Engage the 7 clips and install the instrument cluster finish center panel.



5. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY (for Front Passenger Side)
  1. Engage the 3 claws and install the instrument panel register.



6. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY


    B290425
  1. Engage the 4 guides and 10 clips and install the instrument cluster finish panel garnish.



7. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
  1. Remove the piece of cloth or nylon.

  1. for 6 speakers:

    1. Connect the connector.



    B284321E01
  1. Make sure that the front pillar garnish clip is not damaged.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    1. If there is any damage, replace the garnish clip with a new one.
    2. When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.
  1. Engage the 2 guides.

  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish.

    HINT:
    Tape the needle-nosed pliers tip before use.


    B284391E01
  1. Engage the clip and the front pillar garnish clip to install the front pillar garnish.

    Text in Illustration 
    *1
    Front Pillar Garnish Clip


8. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

HINT:
Use the same procedure as for the RH side.


9. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
  1. for 6 speakers:

    1. Connect the connector.

  1. Engage the 2 guides and the 2 clips and install the front pillar garnish.



10. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

HINT:
Use the same procedure as for the RH side.


11. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



13. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the clip.

  1. Install the cowl side trim board with clip.



14. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


15. INSTALL FRONT DOOR SCUFF PLATE RH (for 5 Door)
  1. Engage the 8 claws and install the front door scuff plate.



16. INSTALL FRONT DOOR SCUFF PLATE LH (for 5 Door)

HINT:
Use the same procedure as for the RH side.


17. INSTALL FRONT DOOR SCUFF PLATE RH (for 3 Door)
  1. Engage the 8 claws and install the front door scuff plate.



18. INSTALL FRONT DOOR SCUFF PLATE LH (for 3 Door)

HINT:
Use the same procedure as for the RH side.


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


20. INSPECT SRS WARNING LIGHT
(Click here)