Engage the guide to install the fog light assembly.

Install the 2 screws.

Connect the connector.

Install the front fender liner with the 2 screws.

Prepare the vehicle:

1. Ensure that there is no damage or deformation of the body around the fog lights.
   
2. Fill the fuel tank.
   
3. Fill the oil to the specified level.
   
4. Fill the coolant to the specified level.
   
5. Inflate the tires to the appropriate pressure.
   
6. Place the spare tire, tools and jack in their original positions.
   
7. Unload the trunk.
   
8. Sit a person of average weight (68 kg, 150 lb) in the driver seat.
   

Prepare the vehicle in accordance with the following conditions:

1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
   
2. Place the vehicle at a 90° angle to the wall.
   
3. Keep a 7.62 m (25 ft.) distance between the center of the fog light bulb and the wall.
   
4. Place the vehicle on a level surface.
   
5. Bounce the vehicle up and down to settle the suspension.
   

HINT:

A distance of 7.62 m (25 ft.) between the vehicle (center of the fog light bulb) and the wall is necessary for proper aim adjustment. If unable to secure a distance of 7.62 m (25 ft.), secure a distance of exactly 3 m (9.84 ft.) to check and adjust the fog light aim (Since the target zone will change with the distance, follow the instructions shown in the illustration.).

Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (high) x 4 m (13.1 ft.) (wide)), to use as a screen.

Draw a vertical line down the center of the screen (V line).

Set the screen as shown in the illustration.

HINT:

1. Stand the screen perpendicular to the ground.
   
2. Align the V line on the screen with the center of the vehicle.
   

Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

HINT:

Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.

1. H Line (Fog light height):
   Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
   

2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) fog lights):
   Draw two vertical lines so that they intersect the H line at each center mark.
   

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light is not being inspected from affecting the fog light aiming.

NOTICE:

Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, and may melt or be damaged due to excessive heat.

Start the engine.

HINT:

Engine speed must be 1500 rpm or more.

Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.

HINT:

1. If the alignment distance is 7.62 m (25 ft.):
   The upper edge of the hot zone for the fog light should be 433 mm (17.06 in.) below the H line.
   
2. If the alignment distance is 3 m (9.84 ft.):
   The upper edge of the hot zone for the fog light should be 52 mm (2.04 in.) below the H line.
   

Adjust the fog light aim to within the specified range by turning the aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.